search

My Binding Challenge Spartan 150M Service Manual Page 25

  • Download
  • Add to my manuals
  • Print
  • Page
    / 61
  • Table of contents
  • TROUBLESHOOTING
    •
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 24
3.0 Maintenance Guide
24
6. Check to make sure the up and down limit switches are positioned properly to prevent gears
from becoming disengaged again (See Section 3.4.9 page 19 and Section 3.4.10 page 20).
7. Replace bottom cover and lay machine flat.
3.5 Troubleshooting
Problem Possible Cause Solution
1. The machine will not
power up – no display,
no line light, and
machine will not cycle.
a) Power cord is disconnected.
b) Main power switch/circuit
breaker is off.
c) Blown fuse on main circuit
board.
d) Disconnected wires inside
machine.
e) No power at electrical outlet.
a) Plug in cord.
b) Turn power switch/circuit
breaker on.
c) Check fuse, replace if blown.
d) Check for wires that are
disconnected from main circuit
board, power cord, etc.
e) Check outlet. Repair or use
another outlet.
2. Display and line light are
on, but machine will not
cycle.
a) Front guard is open.
b) Front guard has not been
opened and closed since
previous cut cycle.
c) Front guard switch needs
adjustment.
d) Knife limit switches need
adjustment.
e) Disconnected wires inside
machine.
f) Faulty cut button.
g) Faulty main circuit board.
a) Close front guard.
b) Open and close front guard.
c) See Section 3.4.8 Front Guard
Switch Adjustment, page 18.
d) See Sections 3.4.9 Knife Up
Limit Switch Adjustment, page
19 and 3.4.10 Knife Down
Limit Switch Adjustment, page
20.
e) Check for wires that are
disconnected from main circuit
board, cut buttons, etc.
f) Check continuity of cut buttons
at circuit board connection.
Replace if necessary.
g) Replace main circuit board.
3. Power is on, but
backgauge display is
blank.
a) Disconnected wires inside
machine.
b) Faulty display circuit board.
a) Check for wires that are
disconnected from main circuit
board, display circuit board,
etc.
b) Replace display circuit board.
4. Backgauge display
shows: “----“.
a) Backgauge has not been
preset.
a) Preset Backgauge by bringing
backgauge to front of machine
(see Operator’s Manual for
more info).
5. Power is on, but line light
does not light up.
a) Disconnected wires inside
machine.
b) Faulty line light circuit board.
a) Check for wires that are
disconnected from main circuit
board, line light circuit board,
etc.
b) Replace line light circuit board.
Page view 24
1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 60 61

Comments to this Manuals

No comments
Related products and manuals for Power universal cutters My Binding Challenge Spartan 150M
Power universal cutters My Binding Standard APC45 Programmable Instruction Manual   (54 pages)
Power universal cutters My Binding Standard PC II- Instruction Manual   (48 pages)
Power universal cutters My Binding MBM Triumph 5550 EP User Manual   (20 pages)
Power universal cutters My Binding MBM Triumph 5550 EP User Manual    (191 pages)
Power universal cutters My Binding Challenge Spartan 150M Service Manual   (42 pages)
Power universal cutters My Binding MBM Triumph 5550 EP Instruction Manual      (41 pages)
Power universal cutters My Binding Challenge Spartan 150M Instruction Manual   (26 pages)
Power universal cutters My Binding Standard PC II- Specifications   (13 pages)
  • AUX Pelican Widex AlpicAir Haier
  • Sony DVD players Schwinn Bicycles Ergotron Mounting kits Black & Decker Power chainsaws Philips Lighting Unknown
  • Carrier 48DD Electrolux EWS10010W Sony DSC-H20 Casio PX-358 Acer Extensa E261
  • Chevrolet CHEVY-2001 Owner's Manual Yamaha PSR-E243 User Manual ZyXEL NBG4115 User Manual Sony CDX-R30M User Manual Philips DVP3345V/17 User Manual